Home > Scsi Error > Scsi Error: Return Code = 0x00010000

Scsi Error: Return Code = 0x00010000

Contents

dmesg info is like : bnx2: eth1 NIC Copper Link is Up, 1000 Mbps full duplex SCSI error : <0 2 0 0> return code = 0x70000 end_request: I/O error, dev Environment SUSE Linux Enterprise Server 11SUSE Linux Enterprise Server 10SUSE Linux Enterprise Server 9 Situation Under certain conditions, SCSI errors can be encountered in /var/log/messages. In response to the second automatic REQUEST_SENSE, the target again issue the same 'Aborted' and 'Internal failure' messages.Depending on the version of the Linux kernel in use, the SENSE key response How could a language that uses a single word extremely often sustain itself? have a peek at this web-site

Here's a paste from /var/log/messages that indicates the basic error: kernel: usb 4-4: new high speed USB device using ehci_hcd and address 22 kernel: scsi20 : SCSI emulation for USB Mass In my case, I did the following: Code: echo 'ST325082:3AS:0x01' > /proc/scsi/device_info The generic solution (according to the last post by Patrick Mansfield on that thread) is the following, assuming that Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign up using Facebook Sign up using Email and Password Post as a guest Name Are you new to LinuxQuestions.org? https://access.redhat.com/solutions/163203

Scsi Error: Return Code = 0x00010000

The behavior is a bit different, because I can write files to the drive (including a 12GB image), but it fails most of the time for writing lots of little files As these messages can be difficult to interpret, this TID is intended to be a brief guide to understanding and decoding these messages.The following is a set of example SCSI errors Command TEST_UNIT_READY (6 bytes) 00 00 00 00 00 00 Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6 usb_stor_bulk_transfer_buf: xfer 31 bytes Status Command READ_10 (10 bytes) 28 00 1d 1c 58 80 00 00 08 00 Bulk Command S 0x43425355 T 0x9 L 4096 F 128 Trg 0 LUN 0 CL 10 usb_stor_bulk_transfer_buf:

In the case of a hex response, further details may be found in scsi.h, or in drivers/scsi/constants.c.In this particular case, the SCSI errors were being generated on the target side (EMC In my case: Code: kernel: usb 4-4: new high speed USB device using ehci_hcd and address 22 kernel: scsi20 : SCSI emulation for USB Mass Storage devices kernel: Vendor: ST325082 Model: Registration is quick, simple and absolutely free. Unhandled Error Code Result Hostbyte=did_error Driverbyte=driver_ok What does the "variable //= a value" syntax mean in Python?

These messages can be informational, or indicate a problem with hardware and/or software. Scsi Error Codes Password Linux - Hardware This forum is for Hardware issues. If so, why is it allowed? https://www.redhat.com/archives/linux-cluster/2007-July/msg00006.html Click Here to receive this Complete Guide absolutely free.

Find More Posts by blue penguin Tags enclosure, hdd, laser, sata Thread Tools Show Printable Version Email this Page Search this Thread Advanced Search Posting Rules You may not post Scsi Error: Return Code = 0x00110018 Contact Us - Advertising Info - Rules - LQ Merchandise - Donations - Contributing Member - LQ Sitemap - Main Menu Linux Forum Android Forum Chrome OS Forum Search LQ Note that registered members see fewer ads, and ContentLink is completely disabled once you log in. Introduction to Linux - A Hands on Guide This guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started

Scsi Error Codes

usb_stor_bulk_transfer_buf: xfer 13 bytes Status code 0; transferred 13/13 -- transfer complete Bulk status result = 0 Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0 scsi cmd done, result=0x0 https://www.veritas.com/support/en_US/article.000015796 every 2 night. Scsi Error: Return Code = 0x00010000 queuecommand called *** thread awakened. Hostbyte=did_no_connect Driverbyte=driver_ok Suggest_ok usb_stor_bulk_transfer_buf: xfer 13 bytes Status code 0; transferred 13/13 -- transfer complete Bulk status result = 0 Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0 scsi cmd done, result=0x0

usb_stor_bulk_transfer_buf: xfer 13 bytes Status code -71; transferred 0/13 -- unknown error Bulk status result = 4 -- transport indicates error, resetting storage_disconnect() called usb_stor_stop_transport called usb_reset_device returns -19 usb_stor_Bulk_reset called http://internetmairie.com/scsi-error/scsi-error-return-code-0x08000002.html thanks I will try to upgrade the kernel version. –Shawn Mar 16 '12 at 15:24 what you're witnessing is not a 'failure possibility', it is 'failure fact'. Command TEST_UNIT_READY (6 bytes) 00 00 00 00 00 00 Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6 usb_stor_bulk_transfer_buf: xfer 31 bytes Status Additional Information Additional information on common SCSI return codes can be found at: http://www.t10.org/lists/1spc-lst.htm DisclaimerThis Support Knowledgebase provides a valuable tool for NetIQ/Novell/SUSE customers and parties interested in our products and Scsi Error Return Code 0x08000002

usb_stor_bulk_transfer_buf: xfer 13 bytes Status code 0; transferred 13/13 -- transfer complete Bulk status result = 0 Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0 -- Result from auto-sense swap controllers or even just switch MOBO connectors –sehe Mar 16 '12 at 15:01 I have change the hardware (move the program to other machine) several times, the hardware Cannot patch Sitecore initialize pipeline (Sitecore 8.1 Update 3) Why were Native American code talkers used during WW2? Source lsmod is as follows: Module Size Used by ehci_hcd 37064 0 usb_storage 81072 16 radeon 110144 1 ntfs 109424 0 irtty_sir 9088 2 sir_dev 19500 1 irtty_sir uhci_hcd 34320 0 piix

How to find the distance between 2 regions? 0x08100002 Document ID:7006510Creation Date:26-JUL-10Modified Date:08-NOV-12SUSESUSE Linux Enterprise Server Did this document solve your problem? They hope these examples will help you to get a better understanding of the Linux system and that you feel encouraged to try out things on your own.

Command READ_CAPACITY (10 bytes) 25 00 00 00 00 00 00 00 00 00 Bulk Command S 0x43425355 T 0x5 L 8 F 128 Trg 0 LUN 0 CL 10 usb_stor_bulk_transfer_buf:

Visit the following links: Site Howto | Site FAQ | Sitemap | Register Now If you have any problems with the registration process or your account login, please contact us. Having trouble installing a piece of hardware? For more advanced trainees it can be a desktop reference, and a collection of the base knowledge needed to proceed with system and network administration. Device-mapper: Multipath: Failing Path The solution is to stop the driver sending REPORT_LUNS to the enclosure.

You are currently viewing LQ as a guest. This book contains many real life examples derived from the author's experience as a Linux system and network administrator, trainer and consultant. usb_stor_bulk_transfer_buf: xfer 13 bytes Status code 0; transferred 13/13 -- transfer complete Bulk status result = 0Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0 scsi cmd done, result=0x0 *** http://internetmairie.com/scsi-error/scsi-error-return-code-0x070e0000.html Share a link to this question via email, Google+, Twitter, or Facebook.