Home > Scsi Error > Scsi Error Pci 8

Scsi Error Pci 8

ok probe-scsi /[email protected],600000/SUNW,[email protected] LiD HA LUN --- Port WWN --- ----- Disk description ----- 0 0 0 2100002037bd356f SEAGATE ST318304FSUN18G 042D 6 6 0 508002000011fd5d SUNW SUNWGS INT FCBPL9216 8 8 If this is not practical, you can use the SunVTS software to test the DVD-ROM. We are also getting a large number of tapes getting marked as Poor, which I am told that could happen if there is a SCSI error. Helpful descriptions for most of the devices are provided to the right of the sample output. Source

Device identification[edit] Parallel Interface[edit] This section may be too technical for most readers to understand. As soon as the AC cord is plugged in, the message "Device POWER SUPPLY plugged in" is displayed. At the ok prompt, type: ok setenv auto-boot? Fibre Channel – Arbitrated Loop (FC-AL) initiators use the LIP (Loop Initialization Protocol) to interrogate each device port for its WWN (World Wide Name). https://vox.veritas.com/t5/NetBackup/Netbackup-scsi-errors-on-Solaris-hw-what-do-they-mean/td-p/288388

According to that u should troubleshoot it. Device Device inserted Advisory Appears as a hot-swap message indicating that a power supply or fan identified by Device was installed without service disruption. Symptom An internal FC-AL disk drive fails to boot, is not responding to commands, or an FC-AL loop fails to initialize. Start/Stop unit: Spins disks up and down, or loads/unloads media (CD, tape, etc.).

Log sense: Returns current information from log pages. The last SPI-5 standard from 2003 also defined a 640MB/s speed which failed to be realized. If you see no front panel LED activity, a power supply may be defective. true false scsi-initiator-id 7 7 oem-logo No default oem-logo?

SASI controller boards were typically the size of a hard disk drive and were usually physically mounted to the drive's chassis. [email protected],1c - expansion backplane Loop A (if installed) c. The SCSI ID, WWN, etc. weblink Note - Environmental monitoring of a power supply occurs only if the power cord is plugged in.

afacey Level 4 ‎02-09-2010 08:47 AM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content Hi All, NBU 6.5.4 Solaris T2000 Use prtdiag with the -l (log) option to send output to a log file in /var/adm. See Sample POST Error Messages and Sample OpenBoot Diagnostics Error Messages for more information. Regards, Arjun Reddy.

LEDs within the enclosure include: CPU/Memory board slot LEDs PCI slot LEDs CPU, I/O, and motherboard fan trays LEDs Disk drive LEDs For detailed information about these LEDs, see the Sun Below the Power button and security keyswitch, a graphical display provides additional LED icons to indicate specific fault conditions and locations. See the prtpicl man page for information. Action Test the drive response to the probe-ide command as follows.

rmt/6 Soft Errors: 0 Hard Errors: 1 Transport Errors: 0 Vendor: IBM Product: ULTRIUM-TD2 Revision: 67U1 Serial No: The staticis get reset after unloading the media. 0 Kudos Reply Contact Privacy http://internetmairie.com/scsi-error/scsi-error-on-write0-16.html Please improve this article by removing excessive or inappropriate external links, and converting useful links where appropriate into footnote references. (February 2015) (Learn how and when to remove this template message) Monitoring Temperatures Temperature sensors are located throughout the system to monitor the ambient temperature of the system and the temperature of each CPU. false false ansi-terminal?

If you've got tapes that old I would start to replace them as you suggest. 0 Kudos Reply Some info Nicolai Moderator Partner Trusted Advisor ‎02-09-2010 11:44 PM Options Mark as Check format output and iostat -En and see if there are any hard errors on the disk. "Device is gone" not necessarily be an internal disk.We need more outputs to verify. The following is sample output from the psrinfo command with the -v option. % /usr/sbin/psrinfo -v Status of processor 0 as of: 04/11/01 12:03:45 Processor has been on-line since 04/11/01 10:53:03. http://internetmairie.com/scsi-error/scsi-error-7932.html Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden.Tek-Tips Posting Policies Jobs Jobs from Indeed What: Where: jobs by Link To This Forum!

false false error-reset-recovery sync sync OpenBoot probe-scsi and probe-scsi-all Commands To diagnose problems with the SCSI or FC-AL devices, you can use the OpenBoot probe-scsi and probe-scsi-all commands. ii states, "9/15/81 first presentation to ANSI committee X3T9-3 (2 weeks following announcement in Electronic Design)." ^ ANSI SCSI Standard, X3.131-1986, June 23, 1986, 2nd, foreword. ^ a b ""How Computer Reboot the system (when convenient) to make the changes effective.

Run OpenBoot Diagnostics and/or SunVTS tests for the system controller card. 8.

Sun Fire V890 Server Diagnostics Guide 817-5950-11 Copyright © 2004, Sun Microsystems, Inc. A screen similar to the following is displayed to indicate that you have successfully reset the OpenBoot NVRAM configuration variables to their default values. SASI is a fully compliant subset of SCSI-1 so that many, if not all, of the then-existing SASI controllers were SCSI-1 compatible.[3] Larry Boucher is considered to be the "father" of false ok reset-all ok probe-ide 2.

I don't believe it was a hardware error as it occured on several severs over a perid of time. Using the two in combination, you can isolate a problem to a particular field-replaceable uint (FRU) with a high degree of confidence. Error messages and other LEDs within the enclosure can help to isolate the problem further. Check This Out RE: fatal scsi error at script address 8 illegal instruction Annihilannic (MIS) 4 Aug 03 10:23 There are a couple of bug reports in SunSolve (1224440 and 1221085 for example) which